Search results

Guess the SSB receive might be right, won't know for sure until I hear some ssb coming in on my 950, then compare that receive somewhat with this receive. I know if I'm on AM and scan across 39, 38, 37 I can hear ssb stations strong rumbling AM, but when I flip to SSB, the signals are very low...

Well, Finished recapping. Replaced all 10v, 16v, 25v caps with new Nichicon types. The 50v caps I didn't replace, their esr and values were still within range. Most of the 10v and some of the 16v caps had very high esr on them, and some would constantly fluctuate readings when testing for...

Testing RF Gain through TR17: Base: RF Gain up = 2.12v RF Gain down = 2.17 Collector RF Gain up = 7.87v RF Gain down = 8.01v. Emitter RF Gain up = 1.42v RF Gain down = 3.28v. From TR17 voltage chart (from cbtricks for 99v): Base - 2.20v Collector - 8.00v Emitter - 1.50v

This one was the good one I guess, lol, replaced it with another good one, which I know is good, but the frequency was still showing 9.89mhz instead of near the 10.240mhz off of pin 4 of the PLL. According to the schematic, pin 3 of the PLL is tied in with TR24 collector lead. The voltage chart...

After looking over the voltages I should see on TR24, comparing it to what I'm actually seeing on TR24 in any mode. Also, after following the schematic and block diagram revolving around TR24, what's tied in with TR24. I'm thinking a disc cap or electrolytic in that general area is the problem...

Got a galaxy Saturn on the desk. Issue is, slightly weak receive on AM, almost non existent SSB receive. Checked RF Gain and Squelch controls, both function properly and smoothly. Checked RF Gain trace from RF Gain control down to TR17, everything looks good. Replaced, C19 C20 C35 C40 C31 C32...

Got a friend that's constantly having an issue with his 148F GTL dropping all output power in AM. I've gone through this radio twice already. The bias caps were dried out, so I replaced those. No mods whatsoever. Changed final with known working one (2312). Changed driver with known working...

How would they mount on the heatsink? There are no screw holes on the heatsink except the 2 in the center to mount the amp.

Thank you for the quick response, Any recommendations on supplier for ones that will mount up to these add-ons?

I've installed several of these new add-on amps and had great success so far. The only issues I'm hearing from people is the following: After constantly talking on it for about 30 minutes, the amp gets scorching hot and power drops back to half the power output, then levels out around 70w to...

Forgot to post the remedy for this issue: It was the voltage regulator transistor mounted on the back left corner (behind power supply) of the radio. Replaced that transistor with one from a spare Saturn and all issues were solved.

Hawkeye, 351, 592 in the Carolina's: Base setup, Original side mounted antron 99. Base of antenna around 18' off the ground. 45' lmr400 coax. Galaxy DX-959 barefoot, 4.5w deadkey, swing to 18w peak on AM, SSB is around 18w. Stock SuperStar handmic. No amp Mobile setup, Old school stainless...

Got an HR - 3950 by Tek on the desk today. Issues: Transmits on just 1 frequency, no matter what band you're in or what the channel indicator says. 24.39....mhz. Transmit is 1w swing to 2w peak in AM. Transmits up to 3w in either sideband. Sideband receive has a high pitched squeal/squall just...

Does this look suspicious to you guys? Tested in circuit shows 47.8 ohms, but seems to be cracked, unless it's just a visual defect. Rest of the topside: Do you guys see anything suspicious, other than that cracked resistor (it tests as 47.8 ohms.

So the 260N should work in place of the 9530, or no it won't? Thank you nomad, you guys have helped me along so much on this site and I value y'all's knowledge.

Thank you shockwave, I looked into those sources, and it seems they do have them in stock. I may have to try some from Roosters. Thank you for that list. As far as my above comment on trying the 260N previously, all I did was replace a blown 9530 with a 260N without adjusting anything and...

I don't understand why the IRFP-260N would not work in place of the ERF9530. The specs seem very close to each other, not much difference at all. Here is the IRFP260N Data: https://alltransistors.com/mosfet/transistor.php?transistor=12899 And here is the ERF9530 Data...

First off, I hope everyone had a safe, peaceful and enjoyable Thanksgiving this year, and I hope the best for your upcoming Christmas holiday. My question is, Does anyone know of any place to purchase ERF9530 transistors for use in the RFX95HD amps? I've done over a dozen installs of these...

32w peak × 1.414 = 45.25w PEP My small MFJ 872 peak meter on my dummy load will read about 28w to 32w peak watts. But on my MFJ 868 True Peak Reading meter (PEP) will show around 40w to 46w PEP on the same dummy load setup. Neither meter has ever been opened at all, bought them new from MFJ...

Happy Thanksgiving everyone on Worldwidedx, I hope you all have a peaceful and enjoyable thanksgiving this year. Please be safe in these troubled times and watch over one another. We all need each other now more than ever. God Bless you and the family. Hawkeye, 351, 592, KM4VAZ around the...