Search results

Version version 1 cable doesn't work need version 2 cable , like stycker cable I been told. my radio came with cable but cable alone doesn't complete conversion. have to go into radio move jumper from 1&2 to 2& 3 and snip white wire, from anytone tec . this version cable plugs into back of...

Software lets you make changes not on menue of radio yes stryker cable works

Look for white wire beside a small black Plug. Move plug from terminal 1 & 2 to 2 & 3 and snip white wire. then use program software to change from 10 meter to CB band which opens all bands for you .I have one and it works great

has white wire to nip and black plug to move from terminal 1&2 to 2&3 side by side on speaker side of board

Bought from Anytone

The mod is simple & easy for 5555N11 version, Small black connector on pin 1&2 move to 2&3 then clip small white wire beside Black connector then radio is on CB bands and wide open use Software to make any changes you might want to..Got this from Anytone after fighting for over a week with them...

If you buy a new Nissan Frontier. You'll find voltage drops to 11.6 at times then back up to 14.2 volts. Factory setting. So I installed a constant voltage box that maintains 13.8 Volts all the time. Nissan says saves gas????Check radio & now a KL503HD box and voltage stays at 13.8 volts all...

Can anyone tell me which pot is for adjusting Watts in a Astatic 600 meter I need to calibrate another used one that seems to be much higher than others I have for Watts , also which diode is for getting swinge in watts reading. It reads watts just no forward swing like my other PDC 's do plus...

I received the MFJ =815D meter, power meter wanted to hang about mid-way power reading then jump up to reading, not long but a second or 2 plus swr was reading about same as pdc600's so I'm sending back, doesn't seem to be any better than my pdc600. By the way PDC600 are no longer made, can't...

I have 2 PDC600, one bought in the 70's and 1 about 10 years ago, I have a MFJ-815D coming. Which of the 3 meters would you say is closer to being correct on everything? Both PDC 600 read about same on SWR & power and Modulation

I need to turn Dead key down on a 13-882C radio,its been teeked out before I got it, keying around 7 modulating to 10 now, I want to use a RK 200p box with it

I just sent one back to Uniden. Started out car charger that came with it wouldn't charge mike. Used my old cell phone charger and charged for over 12 hours then used for a few hours and mike got so it had red led flashing, tried to turn mike off and couldn't get any response out of it. I had to...

I have a bearcat 980 in my shack only keys up 2 watts out of the box with 1.1 SWR ,have a uniden 520XL in truck with 1.1 SWR it only keys up 1.5 watt out of box ,engine off engine on it forwards mod to 4 wats and gives 90watts peak, I'm running 1o2" whip on truck & base , they show no SWR, with...

Thanks for info. I'm not too familiar with insides of these new radios. I can't look at board and know what each section does. Plus in 1973 when I went to school and haven't used my brains much in 50 years working with CB radios and they have gone from coil output to other means, maybe some...

I just checked system again using Peak on my pdc600 meter. I'm getting around 50 on dead key and around 85 watts on modulation, and SWR seems to back up a little while talking on it. Without leaner SWR is 1.1 and box jumps up to about 1.2.5 and then falls back a little while talking. I noticed...

It swings back with 1.5 watts into it and 25watts from Lenear with motor off my radio being new uniden pro 520XL only keys 1.5 watts with dummy load on meter a PDC600 I just checked my PDC meter, it has switch for pep and average, I'll run through more test tomorrow if not raining again

I have a 2 tube Elkin leaner that show a 40 watt swing using same meter 1 watt dead key a uniden 980 SSB

I used a PDC 600 meter and Delta meter to check ,got same reading on both meters

Thanks for answers. I only get approx. 1.5 watts dead key with Nissan truck running giving me around 90 watts dead key only change is increase of voltage to Lenear.. I used CB 23 channel back in the 1970's Have equipment used until 1983 when I moved , seemed like I never had time to get back...