Search results

Thanks Doc, I was looking through the cobra high power mod and noticed that step 9: change C37, and C68 to a .2 monolythic (this changes the A.F. response on TX), so in essence it has a lower freq response correct?

How would you go about it ButtFuzz? a large cap soldered in series? A Potentiometer maybe? I ask this for the fact that I would like to be able to adjust the Audio for Better fidelity without comprimising modulation or doing an NPC mod. Also i want to see /hear the difference in...

A Graphic Equalizer Booster from a car stereo With a Cb? Now for what i was thinking was using a GEQ and rigging a microphone's Tx/audio line to run into the input section of the GEQ and then using the output end to connect back to the mic jack. I know this sounds preposterous,but is it...

Another thing you could do is ask a hvac guy to check if the freon either R22 r134 depending on what the unit uses. sometimes on older machines over time can lose small amounts of gas. Also you could go and clean the heat exchanger coil thoroughly if its blocked with dust dirt grime it wont...

Man Good deal it did not make its way further than that at least i hope not. Did you have to check for any burn marks in your short's after the strike? or was it more of a ooooh Shhh!! kinda reaction?

Thank you for the insight jazz much appreciated. Here is the revised mast , that i just finished mocking up, now it would have been done earlier if i didnt have a 100lb german shepard wanting to play fetch hehe...

Thats what i bought the first time the diamond braided stuff, on special 5.99 for 100 feet, for the metal guy's I'm a little concerned for my two dogs if one were to let go they might get hurt, its also a little less forgiving if one of my dogs runs into it, but they dont seem to have any...

Properties of Nylon Rope | eHow.com

I really appreciate this input guys heres is the shopping list for tomorrow. 2x 100 foot roll of nylon dual core chorde ( unless i can find some sort of turn buckle and 4 foot metal stakes) 1x 10 foot section of conduit 6x 2" Hose clamps 1x Conduit connector 1x Box of self...

Much appreciated Rob that is very usefull information, my roof by the way is about 24 feet tall and has a 45 degree slope and all the other house's aside from my next neighbor to the west are under 20 feet. My entire mast from ground level to the top is roughly 25 feet minus the antenna...

Atm it is 1 inch diamater , i did not like the connecter to much either so i spread som U clamps hangers and put two on opposite sides of each other. I then put my hose clamp ( where i set my guy wires on the lower section of the coduit connecter and another one on the top part. its pretty...

Thanks Mrgumby i think i will do just that, ill go get another 10 foot section and break out the sledge hammer :D

I'm with you ButtFuzz, i call Blasfamy as it is very easy to wrap plastic around an un mounted part with a black tie wrap and say "So an so did this" even most of the hack jobs know how to mount a board! I think someones business is going down and hes just pulling a as seen on tv style...

Went out to home depot this morning to go and get some steel Conduit pipe to make a mast to mount the Maco v 5/8 i ordered from the radio store yesterday :D This is what it looks like mounted to my Deck with some nylon Chord as guy wires...

I feel Sorry for his significant other having to was his fecal stains off his jeans every time he get all rilled up about not having panties on hehe, on a side note i keep hearing some truck wash from NY up here in montreal and tis a pain in the ass.

Atm being 6' 2" i have no problems seeing the radio at all and with the side pannels the way they are made are to flimsy to really support anything but themselves. The pannel only interlocks nearest the seat and is held in place with get this two velcro pads LOL and this is from a car manufature

Alright the rain finally let up and i was given the chance to re work the ground and power leads which are now 17 inches long from a whopping 7 Feet hehe. As well as using a Clip on Style Ferrite ring from and old portable dvd player power coard that is 1 inch long i was able to do 3 loops...

"And when they say it sounds like ass......... You say no it's Uranus!" Awsome that made my day thank you Buttfuzz :D :lol:

Thanks For the Advice Loosecannon, After further pondering of where to mount it i was cleaning the carpets yesterday afternoon just before going to work and noticed that down uder the dash the center console had two removable plastic pannels. The passenger side panel revealed a nice Fuse...

All right so for the jist of it everything is set up in the G6 power wires travel under the rear passenger seat to the Trunk fuse Box and are only seen like in the pics in my Album, coax is passed through the center fold down rear passenger seat and tucked away in the separation of the seat...