Anytone 6666 new

[CB590]

219.00 Calif have it tomorrow free shipping express

the place your ordered it from is a good place to deal with. I've dealt with him before.

enjoy your going to like it. I run mine in frequency mode makes it easier (for me) to go hi/low just by cranking around. I use the mic buttons. Cuts down any channel skipping.

 

[my2995dx]

the place your ordered it from is a good place to deal with. I've dealt with him before.

enjoy your going to like it. I run mine in frequency mode makes it easier (for me) to go hi/low just by cranking around. I use the mic buttons. Cuts down any channel skipping.

View attachment 33930

Fresno Calif is where it.came from waiting on my mount I have a 5ft firestik with the tune tip I might use that but I have a 10k terminator but need the 3 magnet style mount for that.Nice set up you got there like.the one.on the bottom left good set.up

 

[my2995dx]

was looking at the sirio 5000 but a kit is about 90.00 was sure how good they were I heard some say they are good match on the at6666

 

[AudioShockwav]

Fresno Calif is where it.came from waiting on my mount I have a 5ft firestik with the tune tip I might use that but I have a 10k terminator but need the 3 magnet style mount for that.Nice set up you got there like.the one.on the bottom left good set.up

Do you mind saying were in Fresno?
I drive through there sometimes.

73
Jeff

 

[my2995dx]

Not sure where got it online and it shipped from there.Let me look it up and I will let you know.

 

[my2995dx]

DNJ radio he is on eBay

 

[CB590]

DNJ radio he is on eBay

DNJ is also a third party seller on Walmart and NewEgg.

Good guy to deal with. Pricing is good too. I went thru Amzn. But at the time DNJ was willing to drop from then $230 to $220 just by asking via email.

 

[743SEPA]

Stay away from the red devil mike. Like so many Astatic's the ptt switches are so crappy they sound like you're scrubbing it with steel wool when keyed.

 

[Eldorado828]

Stay away from the red devil mike. Like so many Astatic's the ptt switches are so crappy they sound like you're scrubbing it with steel wool when keyed.

I found that out on a rubberized version turned out being the plastic push lever and the round part it pivots on. Used a little bit of dielectric grease and cleared it up but for how long we'll see.

 

[my2995dx]

Had everything hooked up used a universal firestik mount.I put my firestik on some reason couldn't adjust swr's the swr protection kicked on even when I shut it off to try to adjust.I think I'm going to get a magnet mount for my other antenna

 

[CB590]

Had everything hooked up used a universal firestik mount.I put my firestik on some reason couldn't adjust swr's the swr protection kicked on even when I shut it off to try to adjust.I think I'm going to get a magnet mount for my other antenna

That's odd. I run a 5' FireStik on my rear quarter of my truck and never had the issue.

Try a Wilson 5000 maybe.

 

[my2995dx]

That's odd. I run a 5' FireStik on my rear quarter of my truck and never had the issue.

Try a Wilson 5000 maybe.

Think I going to go with my 10k terminator or.a sirio 5000

 

[my2995dx]

Think I found.it ground in coax try it tomorrow and see.I"m using a firestik style coax ground wasn't making contact

 

[CB590]

Think I found.it ground in coax try it tomorrow and see.I"m using a firestik style coax ground wasn't making contact

I was going to ask you about that. I used the factory FireStik coax which is gimpy. I made sure that is was good. It does flex abit at the connector since it's wimpy.

Mine gets out fine and lots of skip contacts running it. Granted mine is a 5' model.

 

[my2995dx]

I was going to ask you about that. I used the factory FireStik coax which is gimpy. I made sure that is was good. It does flex abit at the connector since it's wimpy.

Mine gets out fine and lots of skip contacts running it. Granted mine is a 5' model.

This one I have is 5ft had it for a few years try it again tonight see what happens