• You can now help support WorldwideDX when you shop on Amazon at no additional cost to you! Simply follow this Shop on Amazon link first and a portion of any purchase is sent to WorldwideDX to help with site costs.
  • Click here to find out how to win free radios from Retevis!

Search results

  1. S

    Looking for a Tube tester.

    This is correct. I took the base off a 811 tube to repurpose the socket. Soldered three wires into the sockets filament and grid pins. These wires attach to a 3-500Z socket that has an outboard filament transformer to run the tube. As I recall I am using the 811A test and adjusted the load for...
  2. S

    Looking for a Tube tester.

    Is the tube cracked? If not, it's likely not making a good connection in the socket. The M2057 is exceptionally difficult to find and I've never seen a tube tester with it listed. Although you can test them as a 6KD6, with the filament set for 12 volts. It's worth mentioning the M2057 tube has...
  3. S

    Base New sirio gain master 5/8 improvements ?

    This reinforcing clamp only limits flexing at the antennas first coupling joint. The weakest link, where any flex would be undesirable and cause the top of the fiberglass tube to split. It's not long enough to remove flex in the sections above or below the coupling joint. Had the new...
  4. S

    Maco 300 pumpkin face 1 driving 4 8950 Problems with red plating and have to constantly retune after one minute of no keying

    I've seen that happen with a few of the old red door knobs that they used in Heath kits. There're not as good as the tan colored ceramic ones. I'm sure they didn't use anything quite as good here either. Not that it's required.
  5. S

    Maco 300 pumpkin face 1 driving 4 8950 Problems with red plating and have to constantly retune after one minute of no keying

    "Constantly needing retuning after a minute of no keying", sounds like a fixed value capacitor across the tune or load, is shifting in value as it heats. Not even sure if there is one padding that variable, but it is one of the few things that cause that symptom.
  6. S

    TX Star 250 dx SWR ? (Something lost it's value ?)

    You're not going to like the answer. Your amplifier is oscillating. That is a typical problem with smaller Texas Star amplifiers, due to their bias circuit design, sharing an RF contact on the relay.
  7. S

    Lets talk about replacements for 6lf6 tubes

    No, in fact I've seen one brand like RCA, produce both the single and double versions.
  8. S

    Lets talk about replacements for 6lf6 tubes

    Those 3 amps of filament current, also give the 6KN6, a whooping 1.5 amps of peak cathode current! It has the widest oxide coated cathode of any sweep tube. I bought sleeves of these tubes years ago for $4.99 per tube. I've been using them ever since in every application from a single tube grid...
  9. S

    Either amazon transistors suck, or I am an idiot...

    I think the problem has to do with the DC biasing on your first single-ended transistor driver. Since it is single-ended and NPN, I don't think it should be powered from the same split rail Supply that is feeding the complementary symmetry outputs. If I suspect what is happening is correct, your...
  10. S

    What's inside a 4CX250B tube?

    Not a good idea to crack that BEO ceramic insulator. Any dust particles from the cracked insulator, are highly toxic if inhaled.
  11. S

    High Voltage hijinks, National NCL2000 style.

    With sockets changed and bias reset, it's not hard to get this amp to run inexpensive 4X150A / 7034 tubes. About $50 each for NOS. Even though this version of the tube has 150 watts less dissipation than the 8122, the anode radiator is the same size and there is no noticeable drop in output...
  12. S

    Stryker sr-94hpc

    You'll need a real peek reading watt meter in order to see the 45 watts PEP. Output power is not the problem with that radio. Being able to receive anything through the noise in the mobile environment, is the problem. The radio has no noise blanker, just a mislabeled automatic noise limiter.
  13. S

    Golden Falcon Base Amp - 10 tube

    Use a volt and ohm meter, to start checking for filament voltage and open filaments in the tubes.
  14. S

    FrankenMaco, back from the undead.

    I've been testing everything from 4CX250B, to 8877 on and old Precision tube tester, with an external socket board and a 15 amp filament Transformer. With a bigger filament Transformer, you can test a 10,000 tube. All that's required is a known good tube, to determine the correct load value. If...
  15. S

    Palomar 300A questions

    Nomad has you on the right track. This has nothing to do with the switch, it is the relay this switch is operating. This relay may come back to life with use or flipping the switch a bunch of times. They are difficult to remove the cover and clean without damaging.
  16. S

    Clean Texas Star Sweet 16 for sale.

    I'm glad everything worked out as expected, and everyone is pleased. Nice work on the restoration.
  17. S

    New 32 pill is a dog :(

    This is not a correct diagnosis. When bias does not turn on with a transistor, it works under less stress in class C.
  18. S

    Clean Texas Star Sweet 16 for sale.

    My pleasure Ranch. Glad to see it go to someone who appreciates its 1990, all original factory work. Please let me know once you've had a chance to test it. I want to insure it arrived in good operating condition, as well as physical condition.
  19. S

    I would like an opinion on TL-922A.

    The top section of your DC plate choke, has arced and and fused together. It is visible, with black carbon deposits on the porcelain insulater, in the middle picture of the post I responded to, when you blow it up.
  20. S

    Texas Star DX667V, Relay bad, or parts that trigger the relay?

    I wanted to be an optimist, before having to consider problems under the board.