Search results

channel display was working . till i changed out the lite bulb rx/tx. now the channel display doesn't work. replaced with a new channel display and still not working. where and what would i look to check. thanks allen

does anybody have information on peaking and tuning a cobra 19 DXIV. thanks al

what can i do to a 510 to peak it up. also is there a way to add talkback without a pa system. any help thanks al

does anybody know the sizes and measurements for the frequency and channel displays in cb radios.

959 there was no bulb in it. so i looked at the cbtricks web and found pcb ept55v-51z board which looks just like i got. but where they are showing bulb goes. i try it and no go with 12 volt bulb. there is no solder at those little holes either. could it be one of the resitors burn out before it...

on a 959. is the meter lite a 12 volt or 18 volt. also how and where can i hook a lite up on the meter board for it to dim. where can i buy these bulbs. thanks

148 nw st mic. wiring question. is it a 4 or 5 pin radio. my is 4 pin. if 4 pin hooking up to a cobra microphone. pin 1 shield, 2 audio white, 3 transmit red, 4 rec. black. if its not this please let me know. thats the way i solder microphone and no transmit. thanks al

959 where would i hook the 2 hot wires to from echo board. i read in the other post about disconnecting wire from microphone board pin 2, which wire is that. any other info. would be helpful. thanks allen

would like to know what you all think about comparing cobra 29 to a cobra 148. i'm looking for a nice night watch radio and was thinking between these two radios. i know the 148 has upper/lower which i will never use. i just worder which one could be peaked out the best.

could some body explain how to install echo board. the board is a BB-2 board. i'm going to install the knob on the side of radio. where can i found 9 volts to hook red wire to. does the red and white wire both get hooked to pin 1 of microphone like it states. thanks al

start out with. over 7 diffent cb's, 3 new antennas,4 new mounts and 2 18' coax. 4- new plastic washers on mount to. the problem was with everything i try above. meter runs only at about 1-2 lbs at all times. i get static noise all the time. i can transimit just fine but recice is only good at...

just notice these galaxy 45 radios. are these any good for a trucker radio. or would i be wasting my money. just looking for echo,talkback and a radio that will talk good. i just use channel 19 to. any comments would be helpful. thanks

what can i do to a 979 just for a basic tune up. i cann't find anything on the 979. 959 is loaded with mods.

just wanting to see what you all think about the stryker or the northpoint 9. was thinking of buying one but want feedback on them. and which one would be better then other.

hooking up a patriot on my wooden shed which sits on concret. i going to use a wall mount with a 1 1/4" mast. but was wordering about ground for antenna. if i need ground or not.

it says to cut the circuit board trace to the leg of external speaker jack. what is the trace to the leg. is it the dark green area or light green area around the leg.

have a galxay echo board that is 8 volt. where in a cobra 29 can i find 8 volt on the transmit. so i can solder wire to. its the old echo board. if a resitor is needed what kind or size to use. thanks al

does anybody know where i could pick up the display led's for a galaxy 959. frequency display not channel display. besides ebay. or if anybody has the measurements of them. thanks allen

does anybody know where i could get a new volume/sq control pot at.

can you put a erf 2030 kit into these radios. if so does anybody know where i can get instructions to install the kit.